Discover all new Features of our new Version at a glance.

• Gerber data: Gerber X2 and Gerber X3 implemented
• GenCAD: New functions added. DFM approved.
• Differential Pairs: Easier to create, quicker to connect.

• Panel: Set a Panel outline together with bars inbetween the individual boards
• Multiline Text: Performance improved

• SnapEDA: Interface with SnapEDA. Component not found in TARGET? Load it from SnapEDA. 3D models too!
• Covergence pad: Make any pad a convergence pad. Improve the quality of hand soldered junctions significantly. It's amazing!

• Pilot Router: Direct the path of a track by hovering the cursor tip, a click makes the Pilot Router complete it.
• Give a track a certain length by interactive meandering
• Signal classes can keep special distances between each other
• Tooltip shows all elements superposed at cursor position
• Huge 3D-STEP models can be used at reduced complexity
• Selecting with [Shift] + [M1] also works through nodes and vias
• Track fine tuning: Press [7] to optimize and streamline the selected track segments
• Component buttons in the sidebar collect your favorite parts in their context menu
• Exclude pads for heat sinks: For solder pads and vias the generation of ridges for heat sinks can be suppressed individually

• Push&Shove: When routing a new track, neighboring tracks are pushed aside, if necessary.
  Neighbors of the neighbor follow like a cascade. Spacing rules are obeyed.
• Move vertices to the grid/add any point to the grid: Push&Shove has put some tracks out of the grid? No problem:
  Drag vertices back to the grid by adding the [Shift] key. Or you would generate additional grid points just at the spot where you are.
• Component drag and drop from SamacSys® and UltraLibrarian®
• Selecting track segments: With [Shift] and [Ctrl] as usual in Windows select either "all inbetween" or just the first and last highlighted track segment.
• Design Rule Check: The check for minimum spacings was significantly accelerated.
• Air wires: Number of air wires - A useful little feature to plan and calculate you routing activities.

• Signal polygons: Show or hide signal polygons using keys [<] and [>]
• Builder: COMPONIVERSE extended by the web-based component editor "BUILDER"
• Autosaves: Up to nine renewing autosaves possible instead of only three
• GerberSpecial: XGerber: Standard Gerber file extensions can be chosen
• Printing script format: Printing by scripts now possible in format *.pdf too

• MID-Edition: A click top left upon the "standard orientation"-icon shows the measurements of the MID-body at the bottom left
• Groundplane: Item "Entire PCB area" added to menu "Actions/Ground planes". Use the entire PCB area as a signal polygon.
• Component browser: Properties: Item "Reload properties from a CSV file" added
• Component browser: Component: Item "Generate component from a CSV file" added

• Isolation milling: Tools can be allocated picking them from their place in a jacket.

• Polygonal ground planes: Any filled polygon on a copper layer can be furnished with a signal. Each can be handled like a separate ground plane. It can individually be furnished with attributes. On one copper layer any number of polygons with different signals can be drawn.

• Boost your BoM: Bill of material (BoM): If you add a certain property to a part and you also add the leading characters "BOM-", this particular property automatically will appear in the BoM.

• Engraving bit calculator: Insulation milling: In insulation milling copper tracks are circumscribed by an engraving bit. The width of the rubout depends on the angle of its tip and its immersion depth. Calculate these parameters quickly by the use of the Engraving bit calculator in menu "Engraving Insulation channels".

• Via fence: Signal tracks can on both sides be fenced by a chain of vias. High frequency signals by this means can be shielded from external electromagnetic influence.

• Breadboard: Polygonale breadboard area: Create any polygonal breadboard area in your layout. Hples have the property of a via. You may edit each afterwards or give it a signal. But this is no must. By means of such breadboard areas you easily create "creativity buffers" for your design.

• Password_protection: Protect your project from third party access by the use of a password. But not only a project can be protected: All projects, being created by your license can automatically be protected by a "licence password". This one is demanded if one of your projects shall be opened by a TARGET öicense other than yours. So you protect your intellectual property from third party access. Also a "drift off" towards the spheres of your competitors will be avoided.

• Instant PDF: Create a PDF file of your circuit diagram or PCB without a PDF printer. Achieve a quick transfer of your designs as a PDF.

• COMPONIVERSE®: The interactive component cloud of the TARGET 3001! community. Load up your components and download the ones others have uploaded.
  The TARGET 3001! component exchange. New engine, new look, new features.

• Ask a question: TARGET 3001! internal FAQ system. Correlates to the TARGET dialog from which the question has been asked.

• Components of the British component portal SamacSys can instantly be overtaken to TARGET 3001!. Select components found and place them by drag and drop to your TARGET 3001!-design. Free software "Library Loader" required.

• Pick and place: Individual properties can be processed. In this example it's the properties: STOCK_NO and BOX_NO.

• Introduced "Plugged" and "Capped" for vias and pads (e.g. for thermal vias)

• Pin names in schematic symbols can also have the signal name as text function (e.g. for a RS232 D-sub 9)

• Polygonal pads: Increased visible resolution

• Toolbar: Palette "Tracks": Programmed buttons also affect tracks yet to come

• Symbol generator: Pin numbers also alphanumerical (A1, A2 ... B1 ...)

• Maximum area now 2m x 2m or 6.5ft x 6.5ft.

• Component editor: Get a new component quickly.
• Offers subsequently the automatic functions needed.
• A new symbol and/or package can be derived from existing ones!
• See menu: Components/Create a new component...

• New tool for a quicker design of rectangles.
• Simply enter mesurements in cm or coordinates.
• Drag from the center or from the side.
• See drawing functions

• Text Tag offering useful textfunctions.
• Place comments, advice, notes of any kind to schematic or layout
• See drawing functions