Panel
General
A panel is a multiple placement of projects into one compound. It can be the same project multiplied or different ones having different shapes. The aim is having a maximum utilization of the process format when producing PCB. In TARGET 3001! you easily can multiply your project and not having the numberings counted up (as it is usual in TARGET 3001! when copied and pasted).
Example pic.T3001
We start from our example project pic.t3001. After routing it, it shows as follows:
The function "Set a panel" please find in Menu Actions / Preparatory work / Set PCB as panel...:
After a click on this entry the following dialog opens.
After entering your individual settings (we left the standard settings), the following picture shows:
Use function "Undo" to reduce the panel bit by bit beginning from below right. This function works within the Pin-Limitation of any TARGET 3001! edition. So in a "Light" Edition (400 Pins/Pads) you can not set a project of 250 pins as a panel because the second piece would already exceed the pin limitation. If you set Space X and Space Y each = zero, your board will be V-carved.
Generate bars as predefined breaking points
Image: Bars hold the individual copies in the panel.
You want to set a panel construct bars to break out the individuals later? Here are two options:
Create predetermined breaking points automatically like bars in the panel
Image: Menu Actions/Preparatory work/Panelize PCBs... Set the check mark and press Start.
Image: A dialogue for specifying the entire panel and the predetermined breaking points opens.
At the points where the breakout bars are to dock, always straight line segments must be in the outline (crooked if necessary but straight). TARGET does not dock at bends or kinks at the moment.
Image: The layout may appear like this
Image: 3D- view.
This automatism only works when duplicating one layout as a panel. It does not work with different layouts.
Please also note that "Panelization" only works within the pin limitations of your TARGET 3001! edition.
Create predetermined breaking points as bars by hand in the panel
Versions before V30.2.0.83 do not support the above-mentioned automatism.
Leave ligaments for breaking out the individual boards:
Between the boards, mills on layer 25 (milling) are drawn here manually. For a 2 mm wide milling bit, 2 mm wide brown lines were used. Small bars were left as predetermined breaking points to break out each board later. Please discuss with your PCB manufacturer how the PCBs are to be separated afterwards and how this should look best in your data.
Creating scored panels
Scoring panels can be very practical in production, as the PCBs can simply be broken apart at the scored lines as a predetermined breaking point after assembly. Scoring panels do not need to be milled, which saves time and space. A V-shaped score is drawn through the entire panel, from top and back. This creates the predetermined breaking point:
Image: Scored panel with brown cracks
These settings are required in the panel setting dialog:
Image: "Set panel" dialog
You must check the box "Scored panel" and you can define a margin for the handling.
Merge several layouts to one PCB
Maybe you want to merge two (or more) layouts to one PCB, for producing two or more small PCBs at a time. Principally it works by the use of the clipboard from one project to another. However the components of the layout added are renumbered automatically because TARGET 3001! does not accept two identical component names within one project. R1 of the first layout will be renamed to R12 on the second layout and so on. This might be unwanted in respect to the second layout.
There is a way to keep the numbers so that R1 can appear twice or more:
Open your project which you like to copy and select menu "Actions/Set PCBs as a panel". Internally the component names get adjusted like explained above but the texts shown get separated and become functionally changed from "Component name" to "Normal text". The earlier names within the text field are kept. Now create a panel and copy such a "panel clone" to your other layout. Copy and paste one of the clones of the panel. Don't copy and paste the original one which is top left or the bottom left (depending on how you set the panelization to be going). So you have two different layouts within one PCB-Project and keep identical component namings.
When pasting the layout by the clipboard you give new names automatically to all signals if you get asked for it. So there don't appear unwanted air wires between the PCBs.
Merge several layout modules to one PCB
Say you have created several small layout projects which you now wish to merge to one main project by copy and paste. Act like described above: Create at least a double panel. Here a copy from the initial project is made having the property of holding the component names. Now take such a copy (the original always is the top left one) to your clipboard and paste it to your desired layout.
Turnover panel
Interesting for assembly houses: If a panel is set in such a way that copper top side is mirrored (reversed) to the bottom side, then only one assembly program is required. The bottom and top sides of the panel show the same picture when turned. Also only one stencil is required for the solder paste mask. TARGET offers: Turnover panel right-left or Turnover panel top-bottom. Saves material, saves time, saves money, less harm to the environment!
Image: Selection in the dialog: Turnover panel right-left
Image: Result: Black=Assembly top, Petrol=Assembly bottom
Image: Selection in the dialog: Turnover panel top-bottom
Image: Result: Black=Assembly top, Petrol=Assembly bottom
Catch words:
Panelize different pcbs, multi-pcb, pcbs all in one, more drawing into one board, combining pcbs, pcb group, module layout, copy and paste, panelization.