Torus - Revision history

Markus Friedrich at 14:31, 13 November 2017

2017-11-13T14:31:57Z

← Older revision		Revision as of 16:31, 13 November 2017
Line 17:		Line 17:
	'''Line width:''' Width of the torus line.<br>		'''Line width:''' Width of the torus line.<br>
	'''Aura:''' Width of the spacing between torus and an automatic ground plane. The torus is also drawn in the according deletion layer. The aura is added to the line width.<br>		'''Aura:''' Width of the spacing between torus and an automatic ground plane. The torus is also drawn in the according deletion layer. The aura is added to the line width.<br>
	'''Dotted''' -- '''Rounded ends''': Concerns the line style of the torus		'''Dotted''' -- '''Rounded ends''': Concerns the line style of the torus.<br>
	'''Layer/Page:''' Here you define on which page in the schematic or layer of the PCB this one and future tori will be drawn.<br>		'''Layer/Page:''' Here you define on which page in the schematic or layer of the PCB this one and future tori will be drawn.<br>
	'''Color:''' Standard means what is set within the ini file. Any other color here can be chosen.<br>		'''Color:''' Standard means what is set within the ini file. Any other color here can be chosen.<br>

Markus Friedrich at 14:30, 13 November 2017

2017-11-13T14:30:25Z

← Older revision		Revision as of 16:30, 13 November 2017
Line 16:		Line 16:

	'''Line width:''' Width of the torus line.<br>		'''Line width:''' Width of the torus line.<br>
	'''Aura:''' The torus is also drawn in the according deletion layer. ~~Additionally, the~~ aura ~~value~~ is ~~added to~~ added to the line width.<br>		'''Aura:''' Width of the spacing between torus and an automatic ground plane. The torus is also drawn in the according deletion layer. The aura is added to the line width.<br>
	'''Layer/Page:''' Here you define on which layer of the PCB ~~or page in the schematic~~ this and future tori will be drawn.<br>		'''Dotted''' -- '''Rounded ends''': Concerns the line style of the torus
	'''~~Aura~~:''' ~~Width~~ of the ~~spacing brtween~~ torus ~~and an automatic ground plane~~.<br><br>		'''Layer/Page:''' Here you define on which page in the schematic or layer of the PCB this one and future tori will be drawn.<br>
			'''Color:''' Standard means what is set within the ini file. Any other color here can be chosen.<br>
			'''Signal:''' If the torus is drawn to a copper layer or if it is part of an existing signal, you may either select the signal name here or just view it.<br>
			'''Component:''' If the torus is part of a component, the component name is shown here. But here you can not actively enter a component name in order to assign the torus to a paricular component.<br><br><br><br>

	[[de:Torus]]		[[de:Torus]]
	[[fr:Cercle]]		[[fr:Cercle]]
	[[category:modes]][[category:elements]]		[[category:modes]][[category:elements]]

Markus Friedrich at 14:10, 13 November 2017

2017-11-13T14:10:30Z

← Older revision		Revision as of 16:10, 13 November 2017
Line 11:		Line 11:

	What you can do...<br>		What you can do...<br>
	Place the cursor on the starting point of the torus. Press [o] (for options) for torus settings. The second point you are clicking with [[Mousekeys\|'''M1''']] is the center of the torus and can be entered with '''[Return]''' or [[Mousekeys\|'''M1''']]. The third one is the end point. Are point one and three identical, a full circle will be drawn. These arcs are always drawn in mathematical positive sense (counter clockwise). You can call an options dialog with [[Mousekeys\|'''M11''']] or [o] and enter the following information:<br>		Place the cursor on the starting point of the torus. Press [o] (for options) for torus settings. The second point you are clicking with [[Mousekeys\|'''M1''']] is the center of the torus and can be entered with '''[Return]''' or [[Mousekeys\|'''M1''']]. The third one is the end point. Are point one and three identical, a full circle will be drawn. These arcs are always drawn in mathematical positive sense (counter clockwise). You can call an options dialog with [[Mousekeys\|'''M11''']] or [o] and enter the following information:<br><br>

	[[Image:TorusDlg_e.jpg\|none]]		[[Image:TorusDlg_e.jpg\|none]]<br><br>

	'''Line width:''' Width of the torus line.<br>		'''Line width:''' Width of the torus line.<br>

Markus Friedrich at 14:08, 13 November 2017

2017-11-13T14:08:32Z

← Older revision		Revision as of 16:08, 13 November 2017
Line 13:		Line 13:
	Place the cursor on the starting point of the torus. Press [o] (for options) for torus settings. The second point you are clicking with [[Mousekeys\|'''M1''']] is the center of the torus and can be entered with '''[Return]''' or [[Mousekeys\|'''M1''']]. The third one is the end point. Are point one and three identical, a full circle will be drawn. These arcs are always drawn in mathematical positive sense (counter clockwise). You can call an options dialog with [[Mousekeys\|'''M11''']] or [o] and enter the following information:<br>		Place the cursor on the starting point of the torus. Press [o] (for options) for torus settings. The second point you are clicking with [[Mousekeys\|'''M1''']] is the center of the torus and can be entered with '''[Return]''' or [[Mousekeys\|'''M1''']]. The third one is the end point. Are point one and three identical, a full circle will be drawn. These arcs are always drawn in mathematical positive sense (counter clockwise). You can call an options dialog with [[Mousekeys\|'''M11''']] or [o] and enter the following information:<br>

	[[Image:~~e_TorusDlg~~.jpg\|none]]		[[Image:TorusDlg_e.jpg\|none]]

	'''Line width:''' Width of the torus line.<br>		'''Line width:''' Width of the torus line.<br>

Markus Friedrich at 08:38, 1 June 2011

2011-06-01T08:38:15Z

New page

Also see: [[Circle / slice / ring]], [[Snap Point]] 

You select this feature if you need to draw only a segment of a circle (torus). 
You can reach this mode... 
by '''[t]''' or 
by '''"Draw Torusses"''' in menu '''"Elements"''' or 
by the tool [[Image:Torus.jpg]]. 

Leave this mode... 
by '''[ESC]''' or [[Mousekeys|'''M12''']] 

What you can do... 
Place the cursor on the starting point of the torus. Press [o] (for options) for torus settings. The second point you are clicking with [[Mousekeys|'''M1''']] is the center of the torus and can be entered with '''[Return]''' or [[Mousekeys|'''M1''']]. The third one is the end point. Are point one and three identical, a full circle will be drawn. These arcs are always drawn in mathematical positive sense (counter clockwise). You can call an options dialog with [[Mousekeys|'''M11''']] or [o] and enter the following information: 

[[Image:e_TorusDlg.jpg|none]]

'''Line width:''' Width of the torus line. 
'''Aura:''' The torus is also drawn in the according deletion layer. Additionally, the aura value is added to added to the line width. 
'''Layer/Page:''' Here you define on which layer of the PCB or page in the schematic this and future tori will be drawn. 
'''Aura:''' Width of the spacing brtween torus and an automatic ground plane. 

[[de:Torus]]
[[fr:Cercle]]
[[category:modes]][[category:elements]]